How To Paint C5 Corvette Scuffs Under Door Exterior
The console area is a focal signal in any Corvette interior. Any fourth dimension you have to shift gears or use the heater or air conditioner, you are drawn to this area. If this expanse in the Corvette does not look good, it will make the remainder of the interior look below par. Restoring the 1968-1976 Corvette console is a fairly easy task. The whole shifter console meridian plate tin can be removed as one unit of measurement without whatever special tools. The restoration process is very straight frontwards and all of the console items that you need are available from Nix Corvette Parts. The panel in our 73 Corvette had seen ameliorate days so we decided it was a prime candidate for restoration. The whole process took less than vi hours from beginning to finish and the results speak for themselves. Now let'south get started and give that worn console a brand new look. 1968-1976 Corvette Shifter Panel Restoration:
01: Here are all of the items we received from Null Corvette Parts to restore our 73 panel: Woodgrain trim panel, mounting screws, automatic shift dial indicator, shift lever sliders, A/C-Heater control assembly, heater blower switch, ashtray cover, sliders, and receptacle and the panel engine decal. You volition also need some paint stripper, 1/4" and 1/viii" masking tape, semi-gloss black paint, a scuff pad or 600 grit sandpaper, some mutual mitt tools and a store manual for your year Corvette.
02: Start past disconnecting the battery and removing your Corvette's console top plate assembly from the car. The A/C-Heater controls will stay in the panel. They are removed separately. Information technology is a good idea to tag each light and connection every bit you remove them from the top plate assembly. This makes re-assembly much easier. With the top plate out of the car, remove the woodgrain trim.
03: Carefully remove the engine identification decal. Exercise not pry against the chrome lip around the decal. If you knick it, information technology volition be noticeable when you are finished.
04: Plough the top plate over and remove the ashtray receptacle and socket, the ashtray lid and sliders and the shift dial socket and body assembly.
05: Carefully remove the ashtray chapeau stop. This will have to be re-used. Brand a note where it is located because you will have to replace this in the aforementioned location when you re-assemble it.
06: At present remove the shifter indicator lense and backup. Also remove both shift lever sliders (if the Corvette is an automatic). The console should now be totally disassembled.
07: Use a quality paint stripper and remove all of the black pigment and gum from the console. If you are re-using your ashtray cover, yous will also want to strip it.
08: The new ashtray cover and punch indicator lense backup need to be scuffed before being painted. You lot tin can utilise either a fine scuff pad or 600 grit sandpaper to do the job. Ever sand in ane management. Do not crisscross your strokes.
09: Use 1/4" masking tape to cover the outer chrome border of the console plate. Then use 1/8" masking tape to comprehend the chrome edge effectually the ashtray, A/C-Heater command, shifter, shift dial expanse and engine decal plate. When all of these areas are covered, utilise semi-gloss blackness paint and re-spray the whole console top plate. Use light, even, overlapping strokes. Remember to spray the ashtray comprehend and shift dial backup plate.
x: When the panel pinnacle plate is dry, remove the tape and lay the console woodgrain trim in place with the agglutinative back cover however in place. This will permit y'all to see how it fits. Make a few trial runs to come across how to lay it in place. Once you lot lay the woodgrain trim in place with the adhesive exposed, you will not exist able to re-adjust it. This is a one fourth dimension shot and then make certain you get it right the first fourth dimension. Start at the wide end and work toward the narrow terminate. It works much easier this way.
11: One time the woodgrain trim is in identify, use a bondo squeegee to press information technology into place. Brand sure you lot get it to fit around each raised expanse on your Corvette'south shifter plate.
12: Turn the top plate over and beginning the re-assembly by installing the ashtray chapeau and new sliders. Remember to re-install the ashtray lid stop back in the original place. Y'all may besides want to put some white lithium grease on the area where the ashtray terminate slides confronting the console plate. Now install the new shifter indicator lense, backup and servant. This will at present agree all of these items in place.
thirteen: Install the ii automatic shift lever sliders into place. Make sure you get the large sliders cutting out facing in the right direction.
14: On the right is the new A/C-Heater control associates that Zip provided. Equally you tin can come across, there is a big divergence between this new one and the former i that we removed.
fifteen: Nosotros installed a new heater blower switch on our new A/C-Heater command associates. The installation is very elementary. Just two screws hold it into place. The A/C-Heater control console can at present be re-installed into the retaining plate that is in the car.
16: At present the engine decal tin can be put into place. Remove the protective backing, heart it into its surface area, and press it into identify.
17: Here is the console top plate ready for installation. We placed the A/C-Heater control in its opening so that you lot could come across how the finished product looked. All that is needed now is to re-connect the lights, cables and switches. Screw the console plate into place, re-connect the battery and be proud of a job well done!
1968-1976 Shifter Panel Restoration: How to Restore Your Corvette's Shifter Console
Source: Nothing Corvette Parts
8067 Fast Lane | Mechanicsville, VA 23111 | (800) 962-9632
Corvette Parts List Related to Article:
- 1970L-1971 Motorcar Shifter Console Indicator Lens
- 1972-1976 Automobile Shift Indicator Lens
- 1963-1976 Ash Tray and Lighter Components
- 1970-1976 Shifter Console Trim Plate Forest Inserts
- 1968-1976 Shifter Console Upper Trim Plate Hardware
- 1968-1976 Auto Console Shifter Slide Seals
- Corvette Shop/Repair Manuals
Source: https://www.corvettemagazine.com/1968-1976-corvette-shifter-console-restoration/
Posted by: weaverforrounce.blogspot.com
0 Response to "How To Paint C5 Corvette Scuffs Under Door Exterior"
Post a Comment